Home > Ceramic Discriminator >

Discriminator Electronic Components And Materials

Product Categories

SMD Filter [13]
Ceramic Bandpass Filter [10]
Ceramic Low Pass Filter [11]
455 Khz Ceramic Filter [39]
Ceramic Discriminator [13]
Ceramic Resonator [11]
Crystal Filter [10]
Crystal Resonators [7]
Saw Bandpass Filter [10]
Surface Acoustic Wave Resonator [7]
Piezoelectric Ceramic Actuator [8]
Ultrasonic Atomizing Transducer [11]
Piezoelectric Ceramic Sensor [7]
Ultrasonic Welding Transducer [7]
Piezoelectric Ceramic Transducer [4]
Microwave Bandpass Filters [17]
Microwave Low Pass Filter [15]

hanse-john electronic Co.,Ltd.

Contact Now

Discriminator Electronic Components And Materials

Ask Lasest Price
Brand Name :	HM
Model Number :	KHZ
Certification :	Rohs
Price :	€0.15
Payment Terms :	T/T, Western Union, MoneyGram
Supply Ability :	1000000
Delivery Time :	35 day

Add to Cart

Product Details
Company Profile

Discriminator Electronic Components And Materials

Piezoelectric Ceramic Discriminator CDBCB455KCAY24-R0 CDBc455C24 Alternative model:JGK04-0155K

１． Scope

The specification applies to the discriminator for IF demodulation used in communications equipment .

２．Spec No.:HM-180059

３．Part No.:CDBC455C24

4． Input signal condition

NO.	Item	Specification
4 – 1	Input level	-27.0dBm
4 – 2	Deviation	±1.5KHz
4 – 3	Frequency Modulation	1.0 khz

5．Electrical Characteristics

NO.	Item	Specification
5 – 1	Modulation Frequency	455±1.0KHz
5 – 2	Demodulated Bandwidth(3dB)	±4.0KHz min (from 455 kHz)
5– 3	Demodulated Output	100±40mV. (at 455 kHz)
5 – 4	Demodulated Distortion Factor	2.0%Max.
5 – 5	Withstand Voltage	D.C. 50V for 1 minute

6. :Measurement

6－１． Measurement Condition

Unless otherwise sepecified ,the shandard range of atmospheric conditions for measurements and tests are as follows:

Ambient temperature:5℃ to 35 ℃ Relative humidity :45% to 85%

Air pressure :86Kpa to 106 Kpa

If there is doubt about the results, measurement shall be made within the following limits:

Ambient temperature:18℃ to 22 ℃ Relative humidity :60% to 70%

Air pressure :86Kpa to 106 Kpa

6－２． Measuring Circuit

Discriminator Electronic Components And Materials

6－3． Test Method

Input signal condition	Input level	80dBμ
	Frequency Deviation	±4.0 kHz
	Modulation Frequency	1.0 kHz
Demodulated 3dB Bandwidth	Input the above signal and sweep the carrier around 455 kHz, and find Out the maximum audio output frequency. Then sweep the carrier frequency again and find two frequencies, which are observed –3dB attenuation points from the maximum point. Higher frequency point is called (f1) and lower called (f2). (F1-455KHz) is defined as upper 3dB bandwidth and (455KHz-f2) defined as lower 3dB bandwidth.
Demodulate Output	Demodulated output shall be measured when carrier frequency is adjusted to 455KHz.
Demodulated Distortion Factor	Carrier frequency is adjusted to 455KHz.And distortion shall be measured with 1 kHz modulation frequency.

7．/outline

7-1．

Appearance:Mark shall be clear,appearance shall be smooth and no damage.

7-2．

Material List

NO.	Item	Specification
1	Case	Polybutenetelephthalate (mixture of glass fiber)
2	Terminal	Phosphor bronze Ag Clad
3	Base Sealing	Epoxy resin

7-3.

Dimensions:(mm)

Discriminator Electronic Components And Materials

(1)(2) Input/Output

(3)Dummy

8．Physical Characteristics

NO.	Item	Measurement condition	Requirement
8－１	Random Drop	Filter shall be measured after 3 times random	No visible damage and it

		drops from the height of 30cm on concrete floor	meet Table 1
8－２	Vibration	Filter shall be measured after being applied vibration of amplitude of 1.5mm with 10-55Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours	No damage and it meet Table 1.
8－3	Solderability	Lead terminals are immersed in aide solder for 5 sec and then immersed in soldering bath of 230±5℃, for 3±0.5 sec.	At least 95% lead terminals shall be covered with solder.
8－4 (１)	Terminal strength Pulling	After force of 1kg for 10 seconds is applied to each terminal in axial direction, Filter shall be measured.	No damage, no cut-off and it meet Table 1.
(２)	Bending	After lead terminals shall be fixed at 2mm from filter’s body, they shall be folded up to 90°from their axial directions and folded back to –90°.Then folded back to their axial direction, the speed of folding be each 3 seconds.	No damage, no cut-off and it meet Table 1.

9．Environmental Characteristics

NO.

Item

Measurement condition

Requirement

9 – 1

Humidity

After being placed in a chamber with 90-95% R.H. at 40±2℃ for 100 hours and then being placed in room temperature for 1 hour, filter shall be measured.

It shall meet Table 1.

9 – 2

Resistance to

Solder Heat

It shall meet Table 1.

		Lead terminals are immersed up to 1.5mm from filter’s body in soldering bath of 350± 10℃, for 3±0.5 sec. And then filter shall be measured after being placed in room temperature for 1 hour.
9 – 3	High Temperature	After being placed in a chamber with 80±2 ℃,for 100 hours and then being placed in room temperature for 1 hour , filter shall be measured.	It shall meet Table1
9 – 4	Low Temperature	After being placed in a chamber with -20±2 ℃,for 100 hours and then being placed in room temperature for 1 hour, filter shall be measured.	It shall meet Table 1
9 – 5	Heat Shock	After being kept at room temperature, filter shall be placed at temperature of –55 ℃ , for 30 minutes, then be placed at temperature. 85 ℃, for 30 minutes. After that returned to –55 ℃ again. Repeated above cycle for 5 times. After being kept in room temp. for 1 hour, filter shall be measured	It shall meet Table 1

10. Reflow conditions

Discriminator Electronic Components And Materials

Table 1

Item	Specification
Modulation Frequency	455±1.0KHz
Demodulated Bandwidth(3dB)	±4.0KHz min (from 455 kHz)
Demodulated Output	100±40mV. (at 455 kHz)
Demodulated Distortion Factor	2.0%Max.

Product Tags:

Discriminator Electronic Components And Materials

455kHz Electronic Components And Materials

455kHz Active And Passive Components

Discriminator Electronic Components And Materials

Inquiry Cart 0

Send your message to this supplier


*From:	Your email address is incorrect!
*To:	hanse-john electronic Co.,Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Explore more Ceramic Discriminator products from this supplier

Find Similar Products By Category:

Electronic Components & Supplies

Hot Searches: